煤粉预热燃烧特性及动力学分析

2015-04-29 15:02:52左启伟苍大强安霞赵军杨静波
河北科技大学学报 2015年4期

左启伟 苍大强 安霞 赵军 杨静波

摘要:實验利用热重天平,采用非等温燃烧方法研究了国内某炼铁厂高炉喷吹的典型煤粉预热后燃烧特性及反应动力学参数。考察了煤粉在423,473,523,573,623,673,723,773 K 温度等级下,煤粉试样的燃点、燃烧峰值温度、结束温度、综合燃烧特性指数(G)、燃烧峰值速率等动力学特征参数,计算了煤粉燃烧过程的活化能(E)和指前因子(A)。分析结果表明,北区煤粉在423~773 K不同温度等级燃烧过程中,着火点温度最多下降了240 K,失重峰温度最多提前了263 K,最大燃烧速率最大幅度提升了1.29倍,燃烧特性指数最大为29.8倍;从动力学角度分析出两段热解活化能和指前因子之间均存在良好的线性拟合关系,煤粉燃烧为一级反应;煤粉有明显预热效果温度应不低于673 K。

关键词:冶金燃料;煤粉;预热;燃烧;动力学参数

中图分类号:TF5361文献标志码:A

收稿日期:2015-03-11;修回日期:2015-05-07;责任编辑:王海云

基金项目:国家自然科学基金(51034008)

作者简介:左启伟(1980—),男,河北唐山人,博士研究生,主要从事煤粉燃烧方面的研究。

通讯作者:苍大强教授。E-mail:cangdaqiang@metall.ustb.edu.cn

左启伟,苍大强,安霞,等.煤粉预热燃烧特性及动力学分析[J].河北科技大学学报,2015,36(4):431-436.

ZUO Qiwei, CANG Daqiang, AN Xia, et al.Combustion characteristics and kinetic analysis of preheating pulverized coal[J].Journal of Hebei University of Science and Technology,2015,36(4):431-436.Combustion characteristics and kinetic analysis of

preheating pulverized coal

ZUO Qiwei1,2, CANG Daqiang1,2, AN Xia3, ZHAO Jun3, YANG Jingbo1,3

(1.School of Metallurgical and Ecological Engineering, University of Science &Technology Beijing, Beijing 100083, China; 2.State Key Laboratory of Advanced Metallurgy, Beijing 100083, China; 3.Tangshan Iron and Steel Company Limited, Tangshan, Hebei 063016, China)

Abstract:Experimental research on non-isothermal combustion characteristics and dynamics parameters of applied pulverized coal under preheating domestically is conducted with a thermo gravimetric balance. The combustion characteristic parameters such as ignition temperature, peak temperature at maximum weight loss rate, burnout temperature, general burn exponent(G), and maximum combustion rate are studied under different preheating temperatures of 423, 473, 523, 573, 623, 673, 723 and 773 K. The activation energy (E) and frequency factor (A) are also calculated. The results show that for pulverized coal in the North Area, during the preheating process, when temperature varies from 423 K to 773 K, ignition temperature decreases by 240 K mostly, peak temperature at maximum weight loss rate decreases by 263 K at most, maximum weight loss rate increases as 1.29 times, and G increases up to 29.8 times. It shows that there is lining fit result between E and ln A, which proves that the reaction could be regarded as first order reaction. The combustion process behaves greatly when preheating temperature is over 673 K for the pulverized coal.

Keywords:metallurgical fuel; pulverized coal; preheating; combustion; kinetic parameters

以煤代焦是高炉节能降耗的重要途径,而制约喷煤量的主要因素是煤粉的燃烧特性,因为煤粉在高炉的回旋区内停留的时间只有十几毫秒,燃烧时间短是限制喷煤量进一步升高的一个主要因素[1]。过量喷吹煤粉不但会有大量的未燃煤粉进入到高炉渣,还会恶化高炉的操作条件,降低煤粉替代焦炭的经济效益,致使高炉运行不畅,影响正常的生产秩序[2-5]。……

登录APP查看全文