Progress on high energy density lithium batteries by CAS battery research group

2016-03-23 08:24:15CASResearchGrouponHighEnergyDensityLithiumBatteriesforEV
储能科学与技术 2016年2期

CAS Research Group on High Energy Density Lithium Batteries for EV



Progress on high energy density lithium batteries by CAS battery research group

CAS Research Group on High Energy Density Lithium Batteries for EV

(Chinese Academic of Science, Beijing 100864, China)

Increasing energy density of battery will dramatically extend the driving range of electric vehicles. “Strategic Priority Research Program” of the Chinese Academy of Sciences (CAS) was initiated at the November 15, 2013. In this program, the lithium-ion battery of the 3rd generation, solid-state metallic lithium battery, lithium-sulphur battery and lithium-air battery have been investigated. The mass and volume energy density of 24 A·h Li-ion single cell, with nano-silicon carbon material as negative electrode and lithium-rich material as positive electrode is achieved as 374 W·h/kg and 577 W·h/L, respectively. The energy density of 8 A·h solid lithium battery using the solid polymer electrolyte at 60 ℃ is 240 W·h/kg, While the energy density of solid-state lithium battery based on the inorganic ceramic solid electrolyte is also 240 W·h/kg. The energy density of 37 A·h lithium-sulphur battery reaches 566 W·h/kg at room temperature and 616 W·h/kg at 50 ℃. The energy density of 5 A·h lithium-air battery is 526 W·h/kg. However, these batteries are still far away from practical applications in view of satisfying all required performances. Further comprehensive researches on fundamental science and key technology are needed. In addition, the increase of the energy density of batteries will also increase the safety concerns. Therefore, all lithium batteries containing solid electrolytes could become the final solutions for EV batteries.

lithium ion battery; solid-state lithium battery; lithium-sulphur battery; lithium-air battery; high energy density; EV

Lithium-ion batteries have high energy density and cycle efficiency, low self-discharge and no memory effect, and it have wide application prospects in power batteries. The energy density of single power lithium battery mass produced by LG, SDI and CATL reaches 165—180 W·h/kg. According to EV200 made from Beijing Automotive Industry Corporation (BAIC), it costs 14 kW·h per 100 km and the rechargeable distance traveled using the mass produced power lithium battery is about 200 km. When the energy density of single power lithium battery reaches 300 W·h/kg, the rechargeable distance traveled is 470 km and it basically solved the distance nervousness concerned by consumers. When the energy density reaches 400 W·h/kg, the rechargeable distance traveled is 628 km and the single distance is better than that of fuel vehicles. Meanwhile, the average frequency of charging for passenger vehicles can drop greatly. The rechargeable distance traveled will be prolonged if the power consumption per 100 km can further decrease. Hence, developing power lithium battery with high energy density has great significance and influences more in the future.

All countries in the world have paid a great attention to the R&D of power batteries. They develop the national R&D plans and raise the roadmap of medium and long-term technology development of power batteries [1-2]. In 2012, “EV Everywhere” plan was raised by DOE of USA and the energy density was expected to 150 W·h/kg in 2015. The mass and volume energy density was expected to 250 W·h/kg and 400 W·h/L in 2022, respectively. Meanwhile, the battery cost reduced to a quarter. “Joint Center for Energy Storage Research” was started in 2012 by USA, and the energy density was expected to 400 W·h/kg in 5 years. Technology development roadmap of the next generation battery used in vehicles was proposed in 2008 by NEDO of Japan. The energy density of power battery was expected to 150 W·h/kg in 2015 and 250 W·h/kg in 2020. New battery system would be developed and the energy density was expected to 500—700 W·h/kg after the year of 2030. Energy saving and new energy vehicles as the key development field in “Made in China 2025” plan was unveiled by Chinese government in 2015. In this plan, it was suggested accelerating the development of the lithium-ion batteries of the next generation and new power battery systems. The energy density of single cell was expected to 300 W·h/kg in the medium term and 400 W·h/kg in the long term [3].

“Technology focused on the reform of nano-industry” as Strategic Priority Research Program A of the Chinese Academy of Sciences was initiated at November 15, 2013. The goal of the Program is to develop practical lithium battery with the energy density of 300 W·h/kg. The lithium-ion battery, solid-state lithium battery, lithium-sulphur battery, lithium-air battery as well as high level diagnosis and failure analysis technology of battery based on nanomaterials and nanotechnology were investigated. The program takes the management mechanism of competition evaluation and dynamic regulation, and lay emphasis on the realization and assessment of comprehensive technical indicator. As the application- oriented Program, new technology will be developed to replace the existing technology of lithium-ion batteries through the benchmarking of commercial materials and batteries. The Program can provide advanced battery technology reserves for the long term development of power battery industry in China. China EV 100 Forum with the theme of “Building A Competitive-Innovative-Sustainable Industrial Ecology” was hold in Diaoyutai State Guesthouse on Jan. 24th, 2016. On behalf of CHEN Liquan academician and the team of Strategic Priority Research Program A, Professor LI Hong from Institute of Physics, Chinese Academy of Sciences, introduced part of the latest work of the Program. This report gives a preliminary introduction of the investigation on high energy density of lithium battery, and other research progress of the Program will be reported in the near future.

1 The third generation lithium-ion battery

The 1st generation lithium-ion batteries, employing graphite as anode material and lithium cobalt oxide as cathode materials, have been commercialized by Sony Corporation since 1990 and then widely used in consumer electronics. However, it is difficult to apply it massive in the field of power batteries due to the high cost of lithium cobalt oxide cathode materials. Thus, the lithium cobalt oxide cathode materials are gradually replaced by lithium iron phosphate and nickel cobalt manganese based cathode materials, and the energy density of the single cell is approximate 130—250 W·h/kg. The 3rd generation lithium ion batteries utilize Si-based anode materials as a substitute for graphite anode materials, and the energy density of single cell could hopefully achieve 300—350 W·h/kg. It has been reported that Hitachi Corporation designs a 30 A·h-class cell using a Ni-rich layered cathode and Si alloy mixed graphite anode at the 55th battery symposium in Japan in November 2014. Its energy density can reach 335 W·h/kg and the energy density can achieve as high as 350 W·h/kg by further increasing the content of Si in the mixed anode. In recent years, the development of the 3rd generation lithium ion batteries with energy density as high as 350—400 W·h/kg has brought a new sense of hope and vision owing to the appearance of lithium-rich manganese-based cathode materials with the extra high capacity of 300 mA·h/g. Ningbo Institute of Industrial Technology CAS, Institute of Physics CAS and other research teams jointly develop a new high energy density soft package lithium ion battery, which employs nano-Si as the high capacity anode materials, lithium-rich manganese-based cathode materials as the high capacity cathode, 5 V electrolyte and high voltage separator. The capacity of single cell is 24 A·h, and the gravimetric energy density and volumetric energy density can be up to 374 W·h/kg and 577 W·h/L, respectively.

2 Solid-state lithium metal battery

In the long term, it is expected that the energy density of lithium-ion battery could achieve 400 W·h/kg. Higher energy density of the battery can be obtained with metallic lithium anode materials. And it is also possible that the cost of lithium-ion battery employing metallic lithium anode materials could reduce dramatically on account of the utilization of cathode materials without lithium. It should be noted that the research on metallic lithium anode materials have been 50 years. However, the main problems of the application of metallic lithium in nonaqueous electrolyte solution are the formation of lithium dendrite and the chalking of metallic lithium during the charge-discharge process. These can result in the deterioration of the cycling performance and internal short-circuit as well as the poor safety. Metallic lithium battery was abandoned forever by Moli Corporation in 1989 because of the safety problems. Therefore, the safety and cycle performance are the main problems to develop the rechargeable metallic lithium batteries. So far, the development of solid state battery based on solid electrolytes is a feasible roadmap to solve the problems of metallic lithium anode.

As to the low lithium ion conductivity and narrow electrochemical window of PEO, Prof. CUI Guanglei and his group, which are from Qingdao Institute of Bioenergy and Bioprocess Technology CAS, design a new solid polymer electrolyte, starting from the molecular structure which can improve the lithium ion conductivity, by combining ion transport mechanism and multi-scale mechanisms of dynamic transmission. The lithium ion conductivity of solid polymer electrolyte can achieve 4.3×10-4S/cm at room temperature and possess wide electrochemical window. Based on the above research results, the group develops a composite solid polymer electrolyte possessing excellent comprehensive performance with the compositing concept of “rigid-flexible coupling polymer electrolyte”, and an 8 A·h large capacity solid state lithium polymer battery employing metallic lithium anode materials and nickel cobalt manganese-based cathode materials is designed. The energy density of battery can reach as high as 240 W·h/kg. The capacity retention exceeds 86% under a current density of 0.2 C and 60 ℃ after 400 cycles. The solid state lithium polymer battery shows good safety performance. It will not catch fire and explode after four times nail penetration test, which can not be obtained by the traditional lithium ion battery with the liquid electrolyte.

Prof. XU Xiaoxiong and his group, which are from Ningbo Institute of Materials Technology and Engineering CAS, have developed 1—8 A·h single solid-state lithium battery employing transition metal oxide as the positive material, metallic lithium as the negative material, and composite inorganic ceramic material as the solid electrolyte. The cycle performance of the solid state lithium battery was effectively improved by using an innovative interfacial wetting agent strategy. The energy density of the single cell can achieve 240 W·h/kg, and the capacity retention exceed 80% after 500 cycles. In addition, the solid state lithium battery of 2 A·h can display a stable cycling performance at 0.5 C and 90 ℃. It is clearly demonstrated that the solid state lithium battery has an excellent safety performance at high temperatures. However, the solid state lithium battery based on the inorganic solid electrolyte is still far from practical applications.

3 Lithium-sulphur battery

Prof. CHEN Jian and her group, which are from Dalian Institute of Chemical Physics, Chinese Academy of Sciences, have developed S/C composite nano-materials, cathodes with high sulfur loading, and technologies for large-capacity Li-S batteries. With the self-developed materials and technologies, they fabricated single cell exhibiting a rated capacity of 37 A·h and an energy density of 566 W·h/kg at room temperature as well as 616 W·h/kg at 50℃, which are the largest rated capacity and the highest energy density reported to date. The detections were all performed by the third-party. Meanwhile, the Li-S single cells have passed the third-party security tests. Besides, significant progress has been made in Li-S battery pack technology. The developed 1 kW·h Li-S battery pack was tested by the third-party and presented an energy density of 330 W·h/kg. However, at this moment, the cycle number of the Li-S battery with high energy density and large capacity is only 20—30. To actualize the applications of Li-S battery in energy storage, the cycle life and power density should be further improved and the safety issues should be addressed.

4 Lithium-air battery

Prof. ZHANG Xinbo and his group, which are from Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, have developed single Li-air batteries with a capacity of 5 A·h and 51 A·h. Both batteries are assembled with the application of nano-porous metal oxide/carbon composite as the cathode and the surface-modified lithium metal as the anode as well as air management system developed with proprietary intellectual property rights. The mass energy density of the single full assembled Li-air battery with the rated capacity of 5 A·h, which is tested at room temperature, reaches 526 W·h/kg. Simultaneously, the energy density of the Li-air battery model with the rated capacity of 51 A·h is up to 360 W·h/kg, according to the third party. So far, the bottleneck restricting the practical application of Li-air battery lies in the terribly low cycling life and rate performance, thus calling for further efforts in overcoming the key scientific and technological problems such as accumulation of discharge product, decomposition of carbon cathode and electrolyte as well as corrosion of anode.

5 Perspective

The research progress of the high energy density lithium ion battery described above demonstrated clearly that the development of the lithium ion battery and lithium battery with energy density beyond 300 W·h/kgis not only feasible from the principle. Large number of nano-structure electrode materials, separator and conductive additives were used in the above research. And various of nano-sized surficial and interfacial modification technologies and electrolyte additive agent are employed in the control of interface characterization. However, the point is that much of intensive research must be carried out to comprehensively optimize the performance of new lithium-ion battery prototype with high energy density, such as cycling performance, rate capability, high and low temperature properties, self-discharge, battery deformation, safety performance and production technology.

Acknowledgement

Reference

[1] PENG Jiayue,ZU Chenxi,LI Hong. Fundamental scientific aspects of lithium batteries (I)—Thermodynamic calculations of theoretical energy densities of chemical energy storage systems[J]. Energy Storage Science and Technology,2013,2(1):55-62.

[2] LI Hong. Fundamental scientific aspects of lithium batteries (XV)—Summary and Prospect, Energy Storage Science and Technology,2015,4(3):306-318.

[3] National manufacturing Powerhouse Construction Strategy Advisory Committee. The roadmap of the key technology field in “Made in China 2025” plan[EB/OL]. 2015-10-08. http://www.100cc.cn/detail- 6282305.html.

TM 911 Document code:A Article ID:2095-4239(2016)02-177-04

10.3969/j.issn.2095-4239.2016.02.008


登录APP查看全文