高炉中心加焦实验及技术分析

2016-04-05 08:00:24车玉满郭天永
鞍钢技术 2016年1期

车玉满,郭天永,孙 鹏,姚 硕,姜 喆

(鞍钢集团钢铁研究院,辽宁鞍山114009)



高炉中心加焦实验及技术分析

车玉满,郭天永,孙鹏,姚硕,姜喆

(鞍钢集团钢铁研究院,辽宁鞍山114009)

摘要:中心加焦有利于高炉顺行,但如果中心加焦倾角过大和加焦量过多,则造成中心料柱沸点,燃料比上升。利用溜槽结构参数,提出高炉中心加焦溜槽倾角计算方法,模拟计算炉料在炉内二次分布,分析认为球团更容易滚入中心,因此,需要根据炉料结构中球团所占比例,确定是否实施中心加焦。中心加焦量与球团比例相关,球团配比<10%,可以取消中心加焦,当球团配比>15%时,则需要实施中心加焦,此结论得到高炉实验验证。

关键词:高炉;溜槽倾角;中心加焦量;球团配比

车玉满,硕士,教授级高工,鞍山钢铁集团公司一级专家。E-mail:cheyumang2000@sina.com

Experim ent of Adding Coke into Center of Blast Furnace and Technology Analysis

Che Yuman,Guo Tianyong,Sun Peng,Yao Shuo,Jiang Zhe
(Iron & Steel Research Institutes of Ansteel Group Corporation,Anshan 114009,Liaoning,China)

Abstract Adding coke into the center of the blast furnace is conducive to the smooth operation of blast furnace.However,the boiling point of stock column in the center of BF would be increased while the fuel ratio will be also raised if the dip angle at the center of BF where coke is charged is too big and the amount of adding coke is too much.Based on the structural parameters of the chute the method for calculating the dip angle of the chute for adding the coke into the center of BF was proposed.By thismethod the analog computation for the binomial distribution of furnace burden in the furnace can be done.By analysis it is believed that pellets can run down into the center of BF much more easily.So whether the coke is added into the center of BF or not depends on the ratio of pellets in burden composition.The amount of adding coke into the center of BF is related to the ratio of the pellets which will be charged.W hen the ratio of pellets to be charged is less than 10% ,adding coke into the center of BF can be cancelled,butwhen the ratio of the pellets to be charged ismore than 15% ,adding coke into the center of BF has to be done, which has been verified by the testing in the blast furnace.

Key words blast furnace;dip angle of chute;amount of adding coke into center of BF;ratio of pellets

为解决200 kg/t以上煤粉大喷吹所带来中心气流不足问题,1987年日本加古川开发出高炉中心加焦技术,将15%~25%焦炭布于高炉中心区域,在高炉中心形成金字塔形焦炭柱,可以改善高炉块状带和软融带中心区域透气性。

1991年9月,鞍钢学习日本中心加焦技术,在11号高炉(2580 m3)开展中心加焦实验,初始中心加焦1圈,中心加焦量为7.7%,后期中心加焦为3圈,中心加焦量为25%,11号高炉炉顶煤气CO2含量提高1% ,日产量增加74 t、燃料比下降5 kg/t。利用高炉检修休风机会,从炉顶人孔观察料面中心有直径约为1m圆形凸起部分,凸起部分煤气火较大,说明中心煤气流活跃[1],之后中心加焦技术逐渐得到普及。

随着近年来钢铁行业进入微利时期,几乎所有企业都把降低高炉生产成本作为重点,尤其是在降低高炉燃料消耗方面做过大量实验。……

登录APP查看全文