基于准动态模型的提油作业拖轮适用性分析

2017-10-12 01:02:10张明霞刘镇方
海洋工程 2017年4期
关键词:作业模型

张明霞,刘镇方,裴 斐,林 焰

(大连理工大学 船舶工程学院,辽宁 大连 116024)

基于准动态模型的提油作业拖轮适用性分析

张明霞,刘镇方,裴 斐,林 焰

(大连理工大学 船舶工程学院,辽宁 大连 116024)

目前,由于串靠外输方式具有对船舶吨位差异及装载状况要求小、海况适应力强、系泊力小、解脱迅速等优点,而被广泛运用于浮式生产储卸油平台(FPSO)外输作业中。串靠提油作业时,位于穿梭油轮尾部的拖轮能够提供的最大有效拖力直接影响到了作业的安全性。为完善串靠提油作业时所需拖轮拖力的研究,提出更加合理的拖轮选型理论依据,就需要对拖力进行数值计算。首先,对FPSO与穿梭油轮串靠外输系统绕系泊单点旋转时所受风、浪、流等环境载荷进行全面考虑,建立了准动态受力平衡模型;然后,运用经验公式及AQWA软件计算出环境载荷大小,并依据计算结果拟合出环境载荷曲线;最后,配合受力平衡方程求解出能够保障作业安全进行所需的最小拖力。依照此方法计算所得拖力选取的拖轮能够兼顾作业安全性和使用经济性。

浮式生产储卸油平台;串靠外输;穿梭油轮;拖轮;环境载荷;安全作业

Abstract: At present, the offloading in tandem between FPSO and shuttle tanker, which needs little mooring force and can well adapt to different ship tonnages, loading conditions and complexity of the marine environment, has been widely used. During the offloading operation in tandem, the maximum available towing force, provided by the stern tug, has immediate impact on operation safety. In order to perfect the study of required towing force in offloading operation in tandem and put forward a more reasonable theoretical basis for tug selection, the towing force is calculated in this paper. Environmental loads, such as winds, waves and flow, are comprehensively considered, while FPSO and shuttle tanker are circling around the single point. A quasi dynamic equilibrium model is set up and the value of environmental loads is obtained by use of empirical formulas and AQWA-Workbench tools. Finally, by fitting the environmental load curves and using force balance equations, the required minimum towing force for operation safety is calculated. Both operational safety and economical efficiency can be aligned by this towing force to select tug.

Keywords: FPSO; offloading in tandem; shuttle tanker; tug; environmental loads; safety operation

近年来海洋石油开发事业发展迅速,由于浮式生产储卸油平台(floating production storage and offloading units,简称FPSO)具有适应水深范围广、抗风浪能力强、建造成本低、建设周期短、机动性强、可重复使用、风险小等特点,被广泛运用于油田开发中[1]。目前,串靠外输是最常见的FPSO外输方式。进行靠泊时,穿梭油轮一般空载前往FPSO提油,此时穿梭油轮吃水较浅,水面以上的受风面积较大,有海浪时风、浪、流等环境因素可能会造成油轮无法有效进行系泊作业[2]。……

登录APP查看全文

猜你喜欢
作业模型
一半模型
让人羡慕嫉妒恨的“作业人”
作业联盟
学生天地(2020年17期)2020-08-25 09:28:54
重尾非线性自回归模型自加权M-估计的渐近分布
3D打印中的模型分割与打包
作业
故事大王(2016年7期)2016-09-22 17:30:08
FLUKA几何模型到CAD几何模型转换方法初步研究
我想要自由
三十六计第七计:无中生有
一个相似模型的应用