基于虚拟样机的某商用车驾驶室疲劳寿命仿真分析

2017-10-17 03:42:01窦占峰卞学良郝博然
汽车实用技术 2017年18期
关键词:有限元信号分析

窦占峰,卞学良,郝博然

(河北工业大学机械工程学院,天津 300131)

基于虚拟样机的某商用车驾驶室疲劳寿命仿真分析

窦占峰,卞学良,郝博然

(河北工业大学机械工程学院,天津 300131)

针对某商用车驾驶室疲劳寿命问题,基于虚拟样机技术,将有限元分析与虚拟迭代结合起来,对驾驶室进行疲劳寿命仿真分析。在建立驾驶室有限元模型的基础上利用惯性释放法得到激励响应,将车架模型导入到Adams中并转换为柔性体,建立驾驶室-车架刚柔耦合多体动力学模型及七通道激励试验台。对试验场路采信号处理后作为激励输入到模型中进行虚拟迭代得到载荷谱。通过对驾驶室进行疲劳寿命仿真,结果表明大多数仿真结果与路试结果吻合,因此在模型正确的前提下,此方法流程可用于汽车各结构或零部件疲劳寿命分析中。

驾驶室模型;有限元分析;虚拟样机;虚拟迭代;疲劳寿命

Abstract:To solve the problem of fatigue life of a commercial vehicle cab, based on virtual prototyping technology, finite element analysis combined with virtual iteration was used to analyze the fatigue life of a commercial vehicle cab. On the basis of establishing the finite element model of the cab, the inertial release method is used to obtain the excitation response.The frame model is imported into Adams and converted to a flexible body, then the cab-frame rigid-flexible coupling multi-body dynamics model and the seven-channel excitation test stand were established. The signal collected at the test site is processed and input as a stimulus into the model for virtual iteration to obtain the load spectrum. Through the fatigue life simulation of the cab, the results show that most of the simulation results are consistent with the results of road test,therefore, under the premise of the correct model, this method can be used in the structure of the car or parts fatigue life analysis.

Keywords: cab model; finite element analysis; virtual prototyping; virtual iteration; fatigue life

CLC NO.: U467 Document Code: A Article ID: 1671-7988 (2017)18-143-05

前言

随着汽车行业的快速发展,各企业对于产品品质的要求也越来越高。疲劳寿命作为衡量产品品质的重要指标之一,逐渐被人们所重视[1-2]。对汽车结构或者零部件进行疲劳寿命预测的传统方法是在汽车试验场进行路试试验,而这种方法虽然可靠性高,但会消耗大量时间和财力[3-5],因此亟需一种更高效的方法来进行疲劳分析。

虚拟样机技术基于试验场采集的路试信号,在Adams中建立汽车结构或者零部件的多体动力学模型,建立相应的试验台或激励,再结合虚拟迭代技术和有限元分析对汽车结构或者零部件进行疲劳寿命分析。……

登录APP查看全文

猜你喜欢
有限元信号分析
信号
鸭绿江(2021年35期)2021-04-19 12:24:18
隐蔽失效适航要求符合性验证分析
完形填空二则
电力系统不平衡分析
电子制作(2018年18期)2018-11-14 01:48:24
基于FPGA的多功能信号发生器的设计
电子制作(2018年11期)2018-08-04 03:25:42
电力系统及其自动化发展趋势分析
基于LabVIEW的力加载信号采集与PID控制
磨削淬硬残余应力的有限元分析
基于SolidWorks的吸嘴支撑臂有限元分析
箱形孔轧制的有限元模拟
上海金属(2013年4期)2013-12-20 07:57:18