李正东+周志强+袁学文+刘章文
摘 要: 为了实现多通道变形镜驱动和控制,设计由6组模块组成的变形镜驱动器。其中每块模块包括硬件部分和软件部分,硬件部分设计包含电源设计、接口设计、D/A转换及放大设计和FPGA设计,其旨在接收驱动电压组成的矢量数据,并把这些数字信号经D/A芯片转换成模拟电压,随后经射随和高压放大电路输出,作为变形镜陶瓷单元的驱动电压。软件部分设计包含FPGA设计和NIOS设计,其中FPGA从矢量驱动数据中提取属于该驱动模块16个通道的驱动电压,并把每个通道的驱动电压,按D/A转换芯片的时序要求,以串行方式把数据发送给对应的D/A芯片,完成对变形镜陶瓷单元驱动电压的输出。NIOS程序旨在实现对上位机指令的处理和反馈,完成对驱动模块参数的配置、调试和保存以及数据源切换、通道电压设置等功能。实验表明,变形镜驱动器不仅能以200 f/s的速率对96单元变形的镜波前校正功能进行控制,而且能够正确完成与上位机的信息交互。
关键词: 变形镜; 驱动电路; 硬件设计; 软件设计; FPGA; NIOS系统
中图分类号: TN79+2?34; TN247 文献标识码: A 文章编号: 1004?373X(2017)24?0169?06
Abstract: In order to drive and control the multi?channel deformable mirror, a deformable mirror driver composed of six?group modules was designed. The each module is composed of hardware and software. The hardware design includes the power supply design, interface design, D/A conversion and amplification design, and FPGA design, which is aimed at receiving the vector data composed of drive voltage, and converting the digital signals into the analog voltage through D/A chip. And then the analog voltage output by the emitter follower and high?voltage amplifying circuit is taken as the drive voltage of the deformable mirror ceramic unit. The software design includes the FPGA design and NIOS design. The 16?channel drive voltage of the drive module is extracted in the vector drive data through FPGA, and sent to the corresponding D/A chip in the serial mode according to the time serial requirement, so as to output the drive voltage of the deformable mirror ceramic unit. The NIOS program is aimed to process and feed the command from the upper computer; and realize the configuration, debugging and saving of the drive module parameters, data source switchover and channel voltage setting. The experimental results show that the deformable mirror driver can control the wavefront correction function of the 96?unit deformable mirror with the frequency of 200 f/s, and realize the information interaction with the upper computer correctly.
Keywords: deformable mirror; driver circuit; hardware design; software design; FPGA; NIOS system
0 引 言
主动光学系统的关键器件是由压电陶瓷单元组成的变形镜,而变形镜的工作原理是通过改变加在压电陶瓷单元上的电压,从而改变压电陶瓷单元的形变,最终达到改善光束测量的目的。变形镜驱动器[1?2]是负责将一组电压值构成的矢量数据施加到变形镜上,其中每一路电压负责驱动变形镜的一个陶瓷单元。……