压水堆核电厂稳压器热成形封头评定

2019-08-07 02:02:19邓丰黄燕李焕鸣袁宏田雅婧
科技视界 2019年18期

邓丰 黄燕 李焕鸣 袁宏 田雅婧

【摘 要】稳压器是压水堆核电厂一回路冷却剂系统的主设备之一,对整个核电厂的运行和安全起着重要的作用。百万千瓦级压水堆核电厂稳压器采用板焊结构,封头采用低合金钢钢板通过热冲压成形制造。本文基于核电设备建造规范的要求,对稳压器热成形封头的评定进行研究。根据稳压器封头的成形工艺,确定了稳压器封头制造中的主要工艺及关键参数,并明确了评定过程中相关的试验和检验。对评定试验的结果进行了初步统计和分析。结果表明,按既定工艺成形后的封头质量满足规范和设计要求,且各部位的强度均匀性良好。

【关键词】稳压器;热成形;封头;评定

中图分类号: TM623.91文献标识码: A 文章编号: 2095-2457(2019)18-0001-003

DOI:10.19694/j.cnki.issn2095-2457.2019.18.001

The Qualification of the Hot Formed Head of Pressurizer in PWR Power Station

DENG Feng HUANG Yan LI Huan-ming YUAN Hong TIAN Ya-jing

(Science and Technology on Reactor System Design Technology Laboratory, Nuclear Power Institute of China, Chengdu Sichuan 610041, China)

【Abstract】Pressurizer is one of the most important equipments of the reactor coolant system in PWR, and it is key to the security during the operating of nuclear power plant. The Pressurizer is a plate-weld vessel in 1000MW PWR power station, and its heads are hot formed using of low alloy steel plates. Base on the code requirements, this paper researches the qualification of hot formed heads. Examinations and tests shall be carried out during the qualification according to the design and construction rules. The statistical analysis of test data indicates that heads hot formed according to the given forming procedure meet the requirements of the design and construction rules, and the uniformity of strength of heads is perfect.

【Key words】Pressurizer; Hot formed; Head; Qualification

0 前言

穩压器是压水堆核电厂反应堆冷却剂系统的主设备之一,为核安全1级设备。稳压器设计建造规范为《压水堆核岛机械设备设计和建造规则》[1](RCC-M),稳压器为板焊结构,主承压壳体材料均为低合金钢16MND5钢板(RCC-M中牌号),封头采用低合金钢钢板通过热冲压成形。

在RCC-M中,特别规定对于规范1级设备的主要承压部件需要进行制品评定,以验证按既定的大纲制造的制品或部件具有满意的制造过程和使用条件,制品评定是判定制品特性的时机,尤其是制品的独特性及可试验性。根据规范要求,通过制品评定,最终必须满足下列要求[2]:

(1)通过对制品试料化学成分试验测量结果的分析,确认锻件的化学成分分布均匀。……

登录APP查看全文